What size tires fit the S10-Blazers
Login  | |
|
What size tires fit the S10-Blazers - 12/15/2005 1:09:13 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
Naturally there is tons of interest in what size tires fit on the 4x4 S10-Blazers. How big can I go? What size did my truck come with? How much air (psi) should I put in my tires? Plus a whole host of other quesitons related to tires. I will only appempt to answer the specific question, how big can I go?
Some basic info.
All S10-Blazers come with 5on4.75" lug bolt pattern.
Stock factory wheels are 15"x7" with roughly 6" of backspacing.
Typically you don't want to go any wider then 4-4.5" tire then the rim. On the factory 15x7 that means you want to keep the tire narrower then 11.5". 7+4.5"=11.5". Anthing bigger and the tire will wear goofy.
The factory size tires on most S10-Blazers are the following.
205/75R15, 215/75R15, 235/70R15, and 235/75R15.
The drivers side door will have a sticker in it, this sticker will have the size tires your truck came from the factory with. This sticker will also give the recommended psi for each tire.
Why does the tire size vary so much, all depends on the suspension option your truck came with. To find out which option your truck came with you can contact the dealer and request a vin print out. The vin number has all the critical info in it, and the dealer can print out all the options your truck came with. Another place to look is in the glove box, see all those alpha-numeric codes. Each one has a specific meaning.
I know for a fact that 30" tires will fit on both the old and new body sytle S10-Blazers without fender rubbing. That is the largest size tire you can put on without modifing your truck. One caveate, your torsion bars may need to be cranked up a smidge to get back to factory ride height. I give you some example pics.
The pics have my BFG 30/9.5R15 BFG All-Terrain KO tires mountedon my stock '00 S10-blazer wheels. Notice the tires/wheels are the same on both trucks. I have tested both trucks with the 30" tires while wheeling, and can honestly say they do not rub. Some come say the 30" tire will rub on the anti-sway bar at full crank. I say no need to turn the steering wheel that far, and I haven't noticed the rub myself.
Thumbnail Image
Thumbnail Image
Thumbnail Image
Thumbnail Image
 Attachment (4)
< Message edited by Hanr3 -- 12/16/2005 4:35:00 PM >
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 12/15/2005 1:20:15 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
Well, what about 31" tires? What will it take to fit 31" tires on a 4x4?
2" of body or suspension lift is what you need to do to fit 31" tires without rubbing on the fender, provided you are using the factory wheels.
What if I just put on 31" tires. Where will they rub?
The tires will rub at the rear of the front fender well. It will rub on the outside edge of the inner wheel well next to the chrome trim ring.
Attached is a pic of a stock '91 S10-Blazer with 31" tires. He rubs all the time, even going in and out of parking lots.
Thumbnail Image
Thumbnail Image
Attachment (2)
< Message edited by Hanr3 -- 12/16/2005 4:35:33 PM >
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 12/15/2005 1:41:21 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
What about 32" tires on a 4x4. TrailMaster makes a 5" suspension lift that sells for roughly $1300, plus the cost of installation. The recommended tire size is 32" on the factory wheels. Is it worth $1300 bucks plus installation costs to go from a 31" tire to a 32" tire? The 32" tire is only a 1/2" more ground clearance. Whole lot of money for a 1/2".
There must be a more practical way? 2" Suspension lift and fender trimming, or 2"/3" body lift and fender trimming. I figured since I was going to install a body lift so I could work on my tranny and other things much easier, I might as well put on some bigger tires. Took me 6 months to collect everything I needed for what I wanted to pay. Which isn't much.
33" tires.
What will it take to fit 33" tires? Good question. 5" suspension lift and 2" body lift should get it done. I didn't want to spend the money on a suspension lift when I will be doing a solid axle swap next year. So I installed a 3" body lift and trimmed my fenders to fit 285/75R16 Cooper Discovery S/T tires. 285/75R16 tiress are roughly 33"x11.5" on 16 rims. I had to find 16x8" rims that fit the stock 5 on 4.75" lug nut pattern and had roughly 6" of backspacing. Fortunately GM made that happen on several vehicles. Extreme Blazers, Firebirds, and Camaros came from teh factory with 16x8" wheels. Not all years.
The first pic is a comparision of the stock 235 on the left, 30" on the truck and the 33" I wanted to fit on the truck. Long way to go huh?
Second pic is another comparison of the 33" and 235 tire.
The third pic is the 30" after the 3" body lift install. Lots of space, huh.
Thumbnail Image
Thumbnail Image
Thumbnail Image
Attachment (3)
< Message edited by Hanr3 -- 1/11/2006 9:44:48 AM >
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 12/15/2005 1:56:37 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
So what about this trimming?
How much did you have to trim and where from?
Good questions.
I trimmed a wedge/pie shaped piece from the front and back of each fender well. I measured in about 2" and cut up to the body line. I removed the front inner fender wells before I did any cutting. I also had to beat the firewall back about a 1/2" to match the newly cut fender. See the white box in the pic below, that is the area I beat back with a long handled #10 sledge hammer. Real easy to do and only took a minute. I installed some homemade gap guards to keep the mud out of the engine and off the gas tank. Attached them to the front inner fender wells while I had them out. To get the front inner fender wells in place I used 1" long bolt and screwed it to the firewall.
Thumbnail Image
Thumbnail Image
Thumbnail Image
Thumbnail Image
Thumbnail Image
Attachment (5)
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 12/15/2005 2:02:41 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
Last post.
Time for the finishing touches.
So how did it turn out? I'l let you be the judge.
Fisrt pic- the inner fender well is back in place along with the gap gaurd and trim ring.
2nd pic is with the tire installed.
Last pic is my '00 S10-Blazer on the 30" BFG KO sitting next to the '87 sitting on the 285/75R16 Cooper Discovery S/T tires and a 3" body lift. Only place the tires rub is on the frame at full crank. I just dont turn the wheel all the way. So far, NO fender rubbing.
Thumbnail Image
Thumbnail Image
Thumbnail Image
Attachment (3)
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 12/15/2005 6:18:57 AM
|
|
|
swartlkk
Posts: 14532
Joined: 5/1/2005
From: Waterloo, NY
Status: offline
|
Great Info!
Did you add a body lift to your '00? If so, how high and what did you do? Spacers with longer body mount bolts? Let me know. I am definitely interested in having more room to work underneith there.
_____________________________
Kyle-
04 Rainier
My Restoration Projects
Please Do Not PM for Tech Help
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 12/15/2005 12:21:52 PM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
Thanks!!!!
No, I didn't add anything to the '00. She sits on all the stock original parts from the factory. She currently has 108,000 miles and I am still running the same ball joints, tierods, hub bearings, etc. The only things I have done to the '00 is a front brake job last month, tune up, new fuel pump assembly, regular oil changes, and one new ignition control modual.
< Message edited by Hanr3 -- 12/15/2005 12:22:18 PM >
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 9/3/2006 2:05:07 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3482
Joined: 5/11/2005
Status: offline
|
This damage is from a 30" while wheeling. I bottomed out hard.
Had it been a 31" tire the damage would have been greater. Yes, you can "fit" a 31" tire on, however if you are doing any aggressive driving, or any off-roading, you WILL rub. Unless you cranked your tb up, then your going to be blowing out other parts.
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 9/3/2006 1:26:19 PM
|
|
|
Tony Mantelli
Posts: 15
Joined: 8/26/2006
From: Leesburg, Fl
Status: offline
|
i asked my mechanic about the tb's on my old 1/2 ton he said u can crank them up IF you turn them back 1/4 - 1/2 turn from all the way. Ouch that looks like what the 33's did to my 1/2 ton after a hard day of wheelin
_____________________________
1990 blazer 2wd 4.3
4"drop blocks, 2" drop springs, 2" spindles
2Audio Bahn competition 8"in custom box, and a 400watt clarion amp
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 9/5/2006 1:35:35 PM
|
|
|
Blazinchevy01
Posts: 16
Joined: 5/23/2006
Status: offline
|
Hate to tell you man, but i have an 01 blazer (not a ZR2) with 31's on the stock 15 inch rim with no rubbage. And i get asked all the time around here in NC "IS THAT A ZR2? IT LOOKS AWESOME" i've debated on slapping a ZR2 sticker on it to up the value of the truck when i decide to sell it.
|
|
|
|
|
RE: What size tires fit the S10-Blazers - 9/5/2006 3:56:38 PM
|
|
|
iceflames11
Posts: 262
Joined: 3/7/2006
From: Lancaster, NY
Status: offline
|
I have the same problem as Hanr3. 31 inch tires did that and got little chunks taken out of them from the fender. Torsion bars are cranked but they still rub when off-roading.
_____________________________
2000 Blazer LS 4x4 4.3L vortec 4dr
Dynomax catback exhaust, Hypertech PP III, Granatelli MAF, 31's + 2 inch lift
http://www.cardomain.com/ride/2287818
|
|
|
|
 Today's Posts
Most Active Topics
Make A Donation
Forum Rules & FAQ
RSS Feeds
Chevy Blazer Prices
Chevy Blazer
Trailblazer SS
Advertising Info
|
Blazer Forum .com is not affiliated with or endorsed by Chevrolet Motors Division or General Motors.
|
Printable Version
