4.3 performance
Login  | |
|
4.3 performance - 1/14/2008 9:18:42 PM
|
|
|
98*Bravada*
Posts: 7
Joined: 1/12/2008
Status: offline
|
I might be inclined to keep my V6 if I can find some damn performance parts for it anywhere I go all I find are intakes and bolt ons, I'd like to find some forged pistons, rods and a crank with 9:1 or lower compression, and are there any better intake manifolds out there the stock one for lack of a better word sucks...
If I keep the 4.3 V6 then I'm looking to supercharge or turbocharge it and possibly add nitrous and do some headwork...
My engine is out of my 98' Olds Bravada...
< Message edited by 98*Bravada* -- 1/14/2008 9:52:20 PM >
_____________________________
I drive a brown Olds Bravada (basically a Chevy Blazer with upscale trim)
|
|
|
|
|
|
|
RE: 4.3 performance - 1/15/2008 1:16:25 AM
|
|
|
thegr81
Posts: 2621
Joined: 1/16/2007
From: PHOENIX,AZ
Status: offline
|
If your lookin for performance email http://www.blazerforum.com/showprofile.asp?memId=197 this is 02 vortech he has a wealth of knowledge about forced induction on these motors, he has a turbo setup on his that is sweet!!
_____________________________
2001 2wd 4.3 vortec v6
"I'm not fat, I'm a minitrucker"
|
|
|
|
|
|
|
|
|
RE: 4.3 performance - 1/28/2008 12:48:05 PM
|
|
|
TripleBlackBlazer
Site Moderator
Posts: 1964
Joined: 2/13/2007
Status: offline
|
Strong Blazer, those will work for a carb'd or TBI 2.8 or 4.3 through 93 (at the latest). His Olds is a 98. Are there cams and stuff out there for the 2nd Gen 4.3, yes. Will these cams work? Not sure, but I believe the best thing to do is to get a tune. No engine tear-down involved.
_____________________________
|
|
|
|
|
RE: 4.3 performance - 1/28/2008 1:01:00 PM
|
|
|
strong blazer
Posts: 71
Joined: 1/26/2008
Status: offline
|
yea maybe that what he may hav to go with or just get an sb to put in it
|
|
|
|
|
RE: 4.3 performance - 3/9/2008 12:39:02 PM
|
|
|
ChevyBoy413
Posts: 16
Joined: 1/24/2008
Status: offline
|
go to GMperfomance.com or the local chevy dealer and pick up the book they have everything from aluminum racing block to cams and lifter...money but hey at least they actually make things for it
|
|
|
|
|
|
|
RE: 4.3 performance - 3/10/2008 4:13:15 AM
|
|
|
thegr81
Posts: 2621
Joined: 1/16/2007
From: PHOENIX,AZ
Status: offline
|
quote:
ORIGINAL: packofqtips
i'm almost positive that 5.7 pistons work in the 4.3
Not sure about that one, it is a possibility since ours technically are v8's with two cylinders shaved off!!
_____________________________
2001 2wd 4.3 vortec v6
"I'm not fat, I'm a minitrucker"
|
|
|
|
|
RE: 4.3 performance - 3/10/2008 5:54:03 AM
|
|
|
swartlkk
Posts: 14532
Joined: 5/1/2005
From: Waterloo, NY
Status: online
|
Comparing like years, the pistons are the same, as are the lifters, push rods, rocker arms, valve springs, valves, & valve seals. If you want to get right down to it, the individual injector/poppet nozzle in the SCFI injection systems are the same, as are the intake runner, exhaust runner, and the combustion chamber design. Timing sets should be quite similar, but due to the presence of the balance shaft, may differ in how they attach to the cam.
IIRC, the rods are different due to the larger crank rod journal diameters necessary for the increased vibration of the v6 firing order.
You can squeak out some more cubes by offset grinding the crank and using standard 5.7L rods with custom deck height pistons which I believe has the potential to get you around 4.8L.
< Message edited by swartlkk -- 3/10/2008 6:01:51 AM >
_____________________________
Kyle-
04 Rainier
My Restoration Projects
Please Do Not PM for Tech Help
|
|
|
|
|
RE: 4.3 performance - 3/23/2008 7:06:22 PM
|
|
|
95LS
Posts: 150
Joined: 3/23/2008
Status: offline
|
you can always go with custom pistons and rods. i have a 1969 GTO Judge with a 428. it has a 4.18" bore and 4" stroke. it will run me $600+ to get a set of ross pistons. i can save money and get the rods that are sized to a BBC but if i want to stick with the pontiac journal size then it will be quite a bit more. i remember reading a article about a Syclone thats in the 9's and he had custom forged everything to handle it so it can be done.
|
|
|
|
|
RE: 4.3 performance - 3/24/2008 7:02:21 PM
|
|
|
chance91
Posts: 12
Joined: 9/23/2007
Status: offline
|
If you want to know bout pistons check out hotrod magazine, search for high performance 4.3l. The rods are different i'm afraid, this I know. I think the pistons are the same, but I'm sorry, I can't remember. If I were you, I would start with an intake, head work, and a Cam K-Kit, see what you think of that before going all out Forced Induction. GL
|
|
|
|
|
RE: 4.3 performance - 3/25/2008 7:16:18 PM
|
|
|
95LS
Posts: 150
Joined: 3/23/2008
Status: offline
|
you might want to talk to a company that makes chips and find out exactially what you can get away with before you have to srart getting diffrent chips or a whole new computer. thats why i love my 69 GTO judge no matter what head/cam combo i can think of i dont have to get a computer burned to what i have. i have a friend at work that has a 80 something camaro 5 speed with a 305. he put a mild cam in it with a bigger set of roller rockers and upgraded fuel system along with an exhaust and he called up JEt i think it was and told them everything he has done so far and what he wants to do in the future and he got a custom chip made. if youre going to go overboard with the bigger stuff first that might be somethign to consider. personally i would start off with small stuff ( fuel,ignition,exhaust, ) and see if youre happy with what you get and in the long run it will make the bigger stuff ( heads,cam...) work better. im new to the vortecs myself and im trying to figure out what the aftermarket has to offer as far as small stuff.
|
|
|
|
|
RE: 4.3 performance - 4/11/2008 2:22:10 PM
|
|
|
uniondude31
Posts: 7
Joined: 4/11/2008
Status: offline
|
I don't get why the 4.3L V6 isn't as fast as some of the 3.0L or 3.5L V6. It is a very nice engine and for a V6 its freakin HUGE. My question is how come the 4.3L just doesn't have the power or hp as some of the smaller v6's? I think it should be fairly quick. But im jw if you guys know! thanks
(i have a 2002 LS 4dr 4x4 Blazer)
|
|
|
|
|
RE: 4.3 performance - 4/11/2008 2:44:54 PM
|
|
|
swartlkk
Posts: 14532
Joined: 5/1/2005
From: Waterloo, NY
Status: online
|
You are comparing apples and oranges. The 4.3L engine is designed for torque to move a truck. That and it was designed a LONG time ago and is not taking advantage of much of the newer technologies like many other engines are. The 4.3L is a workhorse that will last a VERY long time with proper maintenance.
_____________________________
Kyle-
04 Rainier
My Restoration Projects
Please Do Not PM for Tech Help
|
|
|
|
|
RE: 4.3 performance - 4/11/2008 7:14:00 PM
|
|
|
uniondude31
Posts: 7
Joined: 4/11/2008
Status: offline
|
Yeah, i guess your right. I believe that It's a work horse, and will last a long time. But i see what ur sayin about new modern technology. It just seems it could have better acceleration and even top speed, but i suppose that ur right and that it was designed for torque. Isn't it based on a small block v8? Idk, i just heard that so it may not be true.
|
|
|
|
|
RE: 4.3 performance - 4/11/2008 11:59:41 PM
|
|
|
Taymacjack
Posts: 518
Joined: 7/18/2007
From: Auschwitz, Oregon
Status: offline
|
it true. same as the v-8 except two cylinders are chopped off...
_____________________________
 1995 GMC Jimmy 4x4X2 (I need a outside spare tire carrier...wanna trade for the inside version?)
|
|
|
|
|
RE: 4.3 performance - 4/12/2008 7:36:02 AM
|
|
|
swartlkk
Posts: 14532
Joined: 5/1/2005
From: Waterloo, NY
Status: online
|
It can be made to run better at the top end, but at the expense of low RPM torque. A cam swap can completely change the operating characteristics of the motor. However, to get even more out of it, you really need to do some port work on the heads and a different induction setup (intake, throttle body, injection), headers and a good exhaust system. Get it all together and you've spent way more than most people want to.
Newer engines with variable valve timing, 4 valves per cylinder, etc can be made to have good torque down low and excellent HP up top (4.2L I6 in my Rainier for instance w/ 240ftlbs of torque off idle maxed out at 275ftlbs and 275HP).
_____________________________
Kyle-
04 Rainier
My Restoration Projects
Please Do Not PM for Tech Help
|
|
|
|
|
RE: 4.3 performance - 4/12/2008 6:14:21 PM
|
|
|
blazin 320
Posts: 2
Joined: 4/12/2008
Status: offline
|
the 4.3 is a 5.7 with 2 cylinders shaved off
ALL of the specs bore,stroke are the same
i found a stroker kit online for the 4.3s for around $700
kit includes crank ,rods,pistons
just like turning a 350 into a 383
|
|
|
|
|
RE: 4.3 performance - 4/12/2008 9:26:34 PM
|
|
|
Erpasscb31
Posts: 12
Joined: 4/12/2008
Status: offline
|
Oh thats cool. I didn't know that. Does anyone know the reason why they put the 4.3 v6 instead of the 350? gas maybe? ?
_____________________________
-2002 LS 4dr 4WD Blazer
|
|
|
|
 Today's Posts
Most Active Topics
Make A Donation
Forum Rules & FAQ
RSS Feeds
Chevy Blazer Prices
Chevy Blazer
Trailblazer SS
Advertising Info
|
Blazer Forum .com is not affiliated with or endorsed by Chevrolet Motors Division or General Motors.
|
Printable Version
