FluX On: Air Conditioning Part 3

	Blazer Forum Classifieds Photo Gallery Search Contact BF Sponsors
Blazer News Member List Forum FAQ Timeslips Recalls TSBs Calendars Register Login

FluX On: Air Conditioning Part 3 - Recharging

Printable Version

Blazer Forums >> Mechanical & Maintenance >> Do-It-Yourself >> FluX On: Air Conditioning Part 3 - Recharging

Page: [1]

Message

<< Older Topic Newer Topic >>

FluX On: Air Conditioning Part 3 - Recharging - 3/13/2008 12:16:58 PM

DCFluX

Posts: 67
Joined: 9/25/2006
Status: offline

To recharge an air condioning system you need the proper set of tools.

You need to start off with a set of R-134a gauges. These run about $40-$200 depending on the build quality and who is selling them.

Then you need a vacuum pump. Higher vaccuum is better opposed to higher flow. A DVD I saw from Autozone claims they have them for rent, but I have never been able to find one at any Autozone I have been in. The venturi type pumps are crap and require a monster compressor to supply the 90PSI at 4CFM required for 30 minutes.

A 1.5CFM single stage pump that can achieve 50u of vaccuum is About $135 at http://www.ackits.com/. Don't forget to get some extra deep vane vacuum pump oil, this pump takes 5 ounces.

You will need 1.9 - 2.0 pounds of R-134a which is approximently 3 cans worth. It doesn't matter who made it. The price of R-134 seems to go up in the summer so you should stockpile some in the winter.

If completely recharging the system you may wish to get a can with a UV shot for future diagnoses. I would go with 2 cans of EF Products 301 R-134a and a can of 307 R-134a plus which has the UV shot, O-Ring conditioner and Oil Charge. You will also need a can tap for the R-134a, EF Products 421.

While at Autozone, consult the Hanyes book on the shelf entitled Automotive Heating & Air Conditioning. From the tables look up the fill capacity of your vehicle and memorize them.

For a 99 Blazer it is:

PAG
(V-7 Compressor) 9 oz.
(HT6 Compressor) 8 oz.

R-134a
(Manual Controls) 1.9 lb.
(Automatic Controls) 2.0 lb.

If you flushed the system you will need to add all of the proper type of PAG to the compressor and dryer before reassembly. Compressors can not be flushed so all the oil must be first drained if reusing one. Don't forget to include the amount that is in any of the cans of refridgerant to your measurements. Put half in the compressor and half in the dryer.

Using a 13mm socket, rotate the compressor clockwise to circulate the oil. Do this for about 10 revolutions.

Attach the hose set to both the low side and the high side ports. These will only go on one way. Once on you will need to open the schrader valves, depends on the gauge set, on mine I turn the knobs that are now on the service ports clock wise to push in.

On the gauge set open both sides to the service port by opening both knobs. Once done connect the service line (yellow) to the vacuum pump and switch on. Be sure to open the vacuum pumps vent. The needles should start going negitave and rest as low as they can go, typically -30, Took about 20 seconds for me. Leave the setup to run for 30 minutes.

Before turning off the pump close both the knobs on the gauge set to off. Disconnect the pump. Note the gauge reading and come back in 30 minutes and see if it changed. If it did you have a leak. See if you can hear the hissing to pinpoint it. Do not remove the high or low side hoses from the system as when vacuum is present the scharder valves leak inwards.

If satisfied there are no leaks screw the tap to the first can of R-134a. Be sure the piercing probe is retracted first. Connect to the service hose and pierce the can. Purge the hose by pressing the schrader valve on the gague set. Warning: This will release R-134 in its liquid state. Use a tool while wearing some gloves and have the gauges facing away from you first.

Once purged open both high side and low side valves to allow gas to enter system. Shake the can and notice the sight glass on the gauge set. This is useful in determining when the can is empty. Once the presure has stabilized close the high side valve on the gauges.

Start the car and turn the A/C on MAX and high speed on the fan. Note that the compressor will only run 5 seconds at a time until there is enough gas in the system. Shake the can while holding upside down to give gas in liqu

< Message edited by swartlkk -- 3/13/2008 1:52:17 PM >

_____________________________

I Break Fords. (tm)