Amplifier Specs

	Blazer Forum Classifieds Photo Gallery Search Contact BF Sponsors
Blazer News Member List Forum FAQ Timeslips Recalls TSBs Calendars Register Login

Amplifier Specs

Printable Version

Blazer Forum >> Mechanical & Maintenance >> Do-It-Yourself >> Amplifier Specs

Page: [1]

Message

<< Older Topic Newer Topic >>

Amplifier Specs - 8/18/2006 11:13:35 AM

XBlazer01

Posts: 2659
Joined: 1/14/2006
From: Hampstead Maryland
Status: offline

Slew Rate:

This is a term used to describe how quickly the output of an amplifier can track its input. Slew Rate is usually measured in V / usec. The higher the value (up to a point), the better the amp is at potentially reproducing the subtle nuances and dynamics associated with music reproduction.

Speaker Sensitivity and Efficiency.

Speaker sensitivity is a specification provided by all manufacturers of high-quality speakers. The sensitivity rating has no relation to sound quality, as some of the very best speakers have low ratings. Sensitivity ratings simply tell you how much sound a speaker will produce for a given power input.

Sensitivity ratings are given in decibels per watt at one meter, or db/Wm. So, with an input of one watt (usually white noise), a speaker with a sensitivity of 90 db/Wm will produce 90 decibels of sound at a distance of one meter. A sensitivity of 90 is considered average, with ratings of 87 and below considered low sensitivity and above 93 considered high sensitivity. To increase the volume by 3 db, you must double the power. So, using the example above, to make 93 db you would need two watts, and to make 96 decibels, four watts.

Most of the time your system is cruising along producing only a few watts. You need extra power for loud bass passages, crescendos in classical music, and other highly dynamic passages. Your speakers may need more than 10 times the average power to re-create these dynamic passages accurately, and if you are playing loudly to begin with, you may need an awful lot of power if you have speakers with a low sensitivity rating.

So, when you are buying an amplifier, consider your speakers, your vehicle size and how loudly you want to play. If you have sensitive speakers, you probably will not need as much power -- even 20 clean watts would probably be enough. If your speakers are only moderately sensitive, your vehicle is large or exceptionally noisy at highway speeds and you want to play loudly, you will need more power in order to faithfully reproduce dynamic passages.

"Sensitivity," which is expressed in dB, should not be confused with "efficiency" that is expressed as a percentage of power out relative to power in. Efficiency data for loudspeakers suffers from many problems such as failure to consider variations in frequency response.

Speaker efficiency is the ability of the speaker to do work or use power. The more efficient the speaker; the less power is required for the speaker to produce sound. Voice coil design, type and size of the magnets, speaker cone design and material, speaker size, etc. all play a critical role in determining speaker efficiency. However, speaker size is a good general method for guessing efficiency.

Typical speaker efficiency (for physicists) is about 5%. Meaning that for 100% power input, you get about 5% acoustical work back.

Keep in mind that when considering subwoofers, or any speaker that will get more than ~100 watts RMS of power, these measurements are affected by other factors that make this specification less than useful when choosing between speakers.

THD or Total Harmonic Distortion.

Back in the old days (1982) It was FTC mandated for the manufacturer to provide a comprehensive single criteria power specification. However, with the de-regulation craze of the 80's, this requirement was dropped. This left it up to manufacturers to determine how to advertise and display their product specifications with no commonly accepted standard for emasurement.
I'll attempt to explain how THD is measured.

Of a signal, the ratio of (a) the sum of the powers of all harmonic frequencies above the fundamental frequency to (b) the power of the fundamental frequency.

The THD is usually expressed in percent as distortion factor or in dB as distortion attenuation.

Measurements for calculating the THD are made at the output of a device under specified conditions.

Now, there are

_____________________________