350 Swap Update
Login  | |
|
|
|
|
|
RE: 350 Swap Update - 3/13/2007 6:51:34 PM
|
|
|
Blazin_Jason
Posts: 1067
Joined: 5/17/2006
From: Van Isl, B.C.
Status: offline
|
Damn what motor did he buy you? That's what's holding me back at this point is deciding on what to do for my engine. Rebuild a 350 with 300,000 miles or pull the 350 from my car (under 25K on it). What are they doing to your tranny? I had mine upgraded to v8 clutch pack, bigger servo, new torque, etc. Also what are you doing for an oil pan? If your buying one make sure you get one that matches the rear main seal of your motor.
_____________________________
85 S10 Blazer 4x4, 2 door, undergoing 350 swap, 3" BL, 33''''s
89 Jimmy 4x4, 2 door, 4.3/auto
|
|
|
|
|
RE: 350 Swap Update - 3/14/2007 12:02:13 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3481
Joined: 5/11/2005
Status: offline
|
Good point about the oil pan. GM engines '85 and older had two piece rear main seals.
I would love to drop a 350 into one of my Blazers. I was talking to a guy I used to work with and he will sell me a 4 bolt main for $100. I told him it would be the end of summer before I would buy it. Then I just need to decide which truck it wil go into. Teh '87 off-road toy, or the '00 DD.
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: 350 Swap Update - 3/15/2007 3:09:57 PM
|
|
|
mojoman13
Posts: 221
Joined: 8/21/2006
Status: offline
|
my dad built a 350 from scratch and he was planning on putting it in a project car, but he said i can have it since he doesnt have a project car to put it in lol. aparently it was strong parts in it and the total overal cost of the engine was 2500 canadian and that was with some really good deals from some buddies of his. he said its pushing 300Hp easy so it should do well in my little beast :) im not too sure wat all parts are in it, i know it has a lt1 intake tho that aparently is like a 20Hp bolt on
so it should run well!
and for the tranny i have no idea wat they are doing. my dad told his buddy who owns the tranny shop to get it up to V8 standards and so hes going to do watever he needs to do to it to get it there.
and for the oil pan, im going to order one from www.jagsthatrun.com
they have one that will not interfere with the front driveshaft and stuff so that should work out well
im going to try to pick up most of my parts from jagsthatrun because i have their manual and those parts aparently work
my 350 is all wrapped up right now so i cant really get a picture of it unfortunately
but like i said, my dads just finishing up on a car thats in his shop then were going to slide mine in there and then she will begin
ill post some pics when i get her in the shop
:)
|
|
|
|
|
RE: 350 Swap Update - 3/15/2007 6:48:20 PM
|
|
|
Blazin_Jason
Posts: 1067
Joined: 5/17/2006
From: Van Isl, B.C.
Status: offline
|
Sounds good man. What are your plans for the headers? I bought a used set of the slickfit advanced adapters 4x4 headers for mine. I didn't know what headers would work with a 3" BL and those ones don't wrap around the steering shaft. They aren't a true "header" as some people say, but as long as they work I'll be happy. Get some pics up!
_____________________________
85 S10 Blazer 4x4, 2 door, undergoing 350 swap, 3" BL, 33''''s
89 Jimmy 4x4, 2 door, 4.3/auto
|
|
|
|
|
RE: 350 Swap Update - 3/16/2007 12:27:53 AM
|
|
|
mojoman13
Posts: 221
Joined: 8/21/2006
Status: offline
|
oh cool. well ya the JTR manual suggests some headers that you can use. its actually a really interesting manual. very good points and great instructions on the step by step process
im going to start gathering all the parts i need together here soon. i just cant wait to unwrap my engine cause i havent even seen it yet so i want to see it so bad lol!
|
|
|
|
|
RE: 350 Swap Update - 3/17/2007 12:55:53 AM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3481
Joined: 5/11/2005
Status: offline
|
I agree with the JTR manual. Good book to read before you start the swap.
Partriot just came out with a new header for us. Check them out too.
Def get the pics up.
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: 350 Swap Update - 3/17/2007 2:48:19 AM
|
|
|
mojoman13
Posts: 221
Joined: 8/21/2006
Status: offline
|
ya JTR has a set of hedman headers that are supposed to work decent.
but my truck goes in the shop monday.
i sold my engine and transmission in my truck right now for $800 and the guy that bought it is coming monday to take them both out so its a bonus lol.
so yup its in there monday
ill prob be in there helping the guy take it out
and making sure he doesnt scratch the crap out of my truck trying to get it out lol!
|
|
|
|
|
RE: 350 Swap Update - 3/17/2007 3:25:00 AM
|
|
|
Blazin_Jason
Posts: 1067
Joined: 5/17/2006
From: Van Isl, B.C.
Status: offline
|
Yeah don't let him take it out himself. He's only going to be concerned with the motor and tranny and not so much with the truck. You don't want any wires/hoses getting destroyed if you can help it.
_____________________________
85 S10 Blazer 4x4, 2 door, undergoing 350 swap, 3" BL, 33''''s
89 Jimmy 4x4, 2 door, 4.3/auto
|
|
|
|
|
RE: 350 Swap Update - 3/17/2007 10:23:29 AM
|
|
|
drperry
Posts: 3901
Joined: 1/12/2007
From: GP AB CA
Status: offline
|
quote:
ORIGINAL: Hanr3
I agree with the JTR manual. Good book to read before you start the swap.
Partriot just came out with a new header for us. Check them out too.
Def get the pics up.
How is it on info for the 2nd gen Blazer? The website lists stuff that's mostly for the 1st gen, and mostly 2wd parts...
_____________________________
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 1:27:40 AM
|
|
|
mojoman13
Posts: 221
Joined: 8/21/2006
Status: offline
|
quote:
ORIGINAL: Blazin_Jason
Yeah don't let him take it out himself. He's only going to be concerned with the motor and tranny and not so much with the truck. You don't want any wires/hoses getting destroyed if you can help it.
wow great point
thx ya ill make sure to keep an eye on them for sure!
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 6:51:37 PM
|
|
|
Hanr3
Wheels & Tire Moderator
Posts: 3481
Joined: 5/11/2005
Status: offline
|
quote:
ORIGINAL: drperry
quote:
ORIGINAL: Hanr3
I agree with the JTR manual. Good book to read before you start the swap.
Partriot just came out with a new header for us. Check them out too.
Def get the pics up.
How is it on info for the 2nd gen Blazer? The website lists stuff that's mostly for the 1st gen, and mostly 2wd parts...
My version has a little info about the swap. Maybe the newer version has more info.
_____________________________
"Some people spend an entire lifetime wondering if they made a difference.
The Marines don't have that problem."
-President Ronald Reagan
'87 S10-Blazer - SOLD
'93 S10-Blazer 4x4x4 - Sons DD, engine swap is done.
'00 S10-Blazer 4x4x4 - My
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 9:32:19 PM
|
|
|
mojoman13
Posts: 221
Joined: 8/21/2006
Status: offline
|
my verson of the manual is mostly for the mid 80's to early 90 blazers
not much info on the newer generation :(
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 9:50:18 PM
|
|
|
drperry
Posts: 3901
Joined: 1/12/2007
From: GP AB CA
Status: offline
|
Bollocks! lol
_____________________________
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 10:23:10 PM
|
|
|
Jman
Posts: 448
Joined: 1/14/2006
Status: offline
|
You will love your blazer with a V8 in it. I want to do this swap to my 95 when the 4.3 dies on me.
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 10:56:32 PM
|
|
|
mojoman13
Posts: 221
Joined: 8/21/2006
Status: offline
|
quote:
ORIGINAL: drperry
Bollocks! lol
hehe i havent been looking for the newer generation stuff in the book but i havent seen any!
and ya i should have some fun with that engine
should impress the kids at school too :P
|
|
|
|
|
RE: 350 Swap Update - 3/18/2007 11:59:52 PM
|
|
|
drperry
Posts: 3901
Joined: 1/12/2007
From: GP AB CA
Status: offline
|
Well, the site says not a whole bunch has changed, so... Maybe they didn't need to change anything, lol.
I'm still gonna try get ahold of an LS7... *grins evilly*
_____________________________
|
|
|
|
|
Printable Version
I'll bring the doughnuts 
Q: motor mounts? - 
